SYSTEMOWE ROZWIĄZANIA HYDROIZOLACYJNE

SYSTEM WATERPROOFING SOLUTIONS

Description

WB INJECTOCREAM is a top quality, ready-to-use, aqueous injection cream based on silanes. In masonry, it penetrates into even the smallest gaps and pores, causing the hydrophobization effect. WB INJECTOCREAM is used for subsequent injections to protect surfaces against moisture. Thanks to a remarkably high content of active substances, it can be used in cases of moisture penetration of up to 95%. Due to its creamy consistency, WB INJECTOCREAM can be applied without the need for laborious preparatory works to be performed, such as filling gaps.

 

APPLICATION:

Tested and certified according to WTA guidelines.

– Ready to use.

– Creamy texture.

Does not contain solvents.

Hydrophobic, no clogging occurs.

Lack of necessity of filling in the identified gaps beforehand.

Excellent penetration properties.

Can be used in cases of moisture penetration up to 95%.

Does not form salts.

Very high concentration of the active substances.

Can be used in no-pressure systems.

 

TECHNICAL DATA:

Basic ingredients: special silanes

Colour: white/yellowish

Application temperature: from +5°C

Density: approximately 0.89 g/cm3

Consistency: paste

Active substance concentration: approximately 82%

Efficiency: depending on wall thickness

 

SURFACE PREPARATION:

Damaged old plaster must be removed at least 80 cm above visible moisture damages. Dusty, brittle, and damaged joints should be removed to the depth of at least 2 cm. Clean the surface mechanically if necessary. Any cracks and open joints must be filled in advance. Afterwards, drill horizontal holes of the diameter of 12 – 16 mm in the support joint at 8 – 12 cm intervals. The depth of the drilled holes should be equal to the wall thickness minus 5 cm (for example: for a wall of the thickness of 40 cm, the depth of the hole should be equal to 35 cm). The holes should be then cleaned with oil-free compressed air. When drilling in two rows, the offset of 8-12 cm must not be exceeded. The use of WB INJECTOCREAM in cellular concrete is possible under certain conditions. Please consult our WB WATER BLOCK Technical Team before its use for the aforementioned purpose.

 

MATERIAL:

Thanks to the use of 1K injection devices or pneumatic syringes with injection lances, WB INJECTOCREAM can be applied in an almost pressure-free manner. The injection is carried out from the bottom of a given hole to its top. To perform said task, insert the lance into the hole and – after activating the injection gun – slowly pull it out of it. The hole must be completely filled with WB INJECTOCREAM. In the case of two-row hole sets, the injection-related procedure should be started from the lower row.

 

EFFICIENCY:

Approximately 1.5 kg per running meter and m2 of wall cross-section. For example: for the wall thickness of 36 cm: 540 g; for the wall thickness of 48 cm: 720 g. It is recommended to ensure the availability of the excess of product of at least 10% of the calculated efficiency. After the injection, the material will be completely absorbed by the wall. Then, fill in the holes with the WATER BLOCK cement mortar. To dry the wall above the injection area, make sure there are no impermeable paints or coatings on it; remove them if necessary. Sufficient drying conditions must be provided and additional measures may have to be taken. Depending on the damages identified and the complexity of the project, further waterproofing may be required, for example – the use of vapor-permeable renovation plaster, as well as external or internal waterproofing of the building basing on the use of WATER BLOCK products.

 

Set contains:

  • 2L of WB Primer for waterproofing,
  • 10 kg of WB Duo Flex waterproofing,
  • 5 m of WB Tape Pro – self-adhesive tape.

 

 

Karta techniczna produktu – pobierz.

Jak możemy Państwu pomóc?

How can we help you?

Służymy Państwu pomocą. W przypadku pytań dotyczących naszych produktów i rozwiązań systemowych prosimy o kontakt telefoniczny.

We are here to help you. If you have any questions pertaining to our products and system-based solutions, do not hesitate to call us.

Bądź z nami na bieżąco!

Stay with us on a regular basis!

Subskrybuj nasze kanały i śledź nasze działania oraz dodawaj opinie :)
Subscribe to our channels and follow our activities and add opinions :)

FACEBOOK

INSTAGRAM

YOUTUBE

Water Block to produkty klasy premium przeznaczone dla klientów ceniących rozwiązania na lata. Długoletnia współpraca technologów z Polski i Szwajcarii pozwoliła na stworzenie kompletnych rozwiązań systemowych dla takich elementów konstrukcyjnych budynku jak balkony, tarasy, dachy oraz fundamenty. Water Block z powodzeniem stosowany jest wszędzie tam, gdzie ważne są takie parametry, jak duża elastyczność, odporność na niskie temperatury, czy wytrzymałość na parcie wody.

Water Block are premium class products designed for customers who value solutions for years. Long-term cooperation of technologists from Poland and Switzerland has allowed us to create complete system solutions for such structural elements of the building as balconies, terraces, roofs and foundations. Water Block is successfully used wherever parameters such as high flexibility, resistance to low temperatures or resistance to water pressure are important.

Godziny otwarcia

Hours opening